Close
0%
0%

RigTig

Maker

Sydney, Australia
Following
Send a private message
Similar accounts worth following
17 Followers
50 Following
5 Projects
101 Likes
rigtig
Send a private message

This user joined on 08/20/2016.

19.6k
4.1k
32
75
A DIY 3D printer (big volume, inexpensive, lightweight and portable).
Project Owner Contributor

RigTig's Big 3D Printer

rigtigRigTig

6k
1.3k
2
10
A cable-less connection for stepper motor control, using Forth
Project Owner Contributor

ESP8266 Stepper Driver

rigtigRigTig

1.6k
11
0
9
To construct a dirt 'hut' for emergency human accommodation using a DIY 3D printer (big volume, inexpensive, lightweight and portable).
Project Owner Contributor

3D Print Emergency Accommodation

rigtigRigTig

1.2k
3
2
7
To program or test ESP-12 or ESP-14 before installation, then plug adapter into breadboard and the ESP into adapter. Unplug when done.
Project Owner Contributor

ESP-12 and ESP-14 adapter to DIL

rigtigRigTig

83
0
0
0
Replacing the door opener electronics with Arduino
Project Owner Contributor

Garage Door Opener

rigtigRigTig

66.7k
150
112
104
Turn cheap modules from AliExpress into interactive development kits!
Project Owner Contributor

eForth for cheap STM8S gadgets

thomasThomas

107.4k
1.2k
93
373
A powder and inkjet 3D printer based on HP45 inkjet technology
Project Owner Contributor

Oasis 3DP

yvo-de-haasYvo de Haas

89.8k
3.6k
84
604
A smaller and cheaper open source brushless motor
Project Owner Contributor

PCB Motor

carl-bugejaCarl Bugeja

87.5k
366
96
287
Software to create your own Knit-like string pictures.
Project Owner Contributor

DIY Knit Portrait

raphael-schaafRaphael Schaaf

40k
1.6k
21
99
Prism is a smart charging station for your electric vehicle.
Project Owner Contributor

Prism

mastro-gippoMastro Gippo

20.7k
4.9k
16
133
Takes 3D surface scans at close range. It is simple to construct as it uses off the shelf hardware and software.
Project Owner Contributor

3D scanner

jolarJolar

16.4k
110
17
91
Testing and development of a system to cut traces on a blank PCB using electro-discharge machining with pencil lead
Project Owner Contributor

PCB Fabrication with EDM

jake-wachlinJake Wachlin

15.8k
2.2k
11
183
This is a design for a low-cost extruder for printing objects directly from recycled plastic flakes instead of using filament.
Project Owner Contributor

Trash Printer - Recycled Plastic 3D Print Head

sam-smithSam Smith

15.6k
87
6
69
An all-in-one solution for controlling microfluidic chips
Project Owner Contributor

Microfluidics control system

craig-watsonCraig Watson

12.3k
3.6k
0
34
Creating copies of keys using a 3d printer and OpenSCAD
Project Owner Contributor

3d Printing real-world keys

dave-peduDave Pedu

7.6k
36
11
26
A front wheel drive, compact, modular bicycle that you build yourself.
Project Owner Contributor

Bellcycles: A New Take on the Bicycle

alex-bellAlex Bell

7k
63
2
69
A hx4k lattice fpga based pulse echo board, yosys compatible
Project Owner Contributor

un0rick - an ice40 ultrasound board

kelu124kelu124

6.3k
45
23
44
Affordable photography tool used to capture images of bullets with no apparent motion blur
Project Owner Contributor

Edgerton, A High-Speed LED Flash

tyler-gerritsenTyler Gerritsen

6.2k
73
36
69
Using a LED/LDR pair to form inverting Photonic logic gates. The entire Boolean logic set handled by resistors and diodes! Who'd'a thunk
Project Owner Contributor

LIGHT LOGIC - HIC SVNT DRACONES

dr-cockroachDr. Cockroach

6k
131
17
108
Using low cost parts to construct a cable robot with incredible capabilities.
Project Owner Contributor

Cable Robot

tomTom

5.2k
218
44
132
[ an open-access peer-reviewed journal ]
Project Owner Contributor

Hackaday Journal of What You Don't Know

aleksandar-bradicAleksandar Bradic

3.6k
21
5
39
A bread board and flash adapter for ESP12 E/F that allows to remove the module after use.
Project Owner Contributor

ESP8266 ESP12E / F bread board and flash adapter

medeiros1medeiros1

3.6k
40
11
25
A proof of concept multipurpose heliostat
Project Owner Contributor

Solar Mirror Array

wkpsahlwkpsahl

3.1k
72
0
36
An open source large format 3D-printer for plastic re-/upcycling
Project Owner Contributor

Bloft Mk2 - 3D printer for plastic waste

atte-linnaAtte Linna

View all

Share this profile

Share

Bits

Dr. Cockroach wrote 08/03/2019 at 13:48 • point

Good morning/evening RigTig and thank you for the follow/like of #Light Logic :-)

  Are you sure? yes | no

Samuel A. Falvo II wrote 09/05/2017 at 15:28 • point

Thanks for the like and follow!

  Are you sure? yes | no

Ulysse wrote 07/07/2017 at 15:34 • point

Hello RigTig, thank you for following Pablo :-)

  Are you sure? yes | no

Eric Hertz wrote 03/18/2017 at 13:32 • point

Howdy RigTig! Thanks for the follow!

  Are you sure? yes | no

Thomas wrote 03/04/2017 at 11:30 • point

The 3D printed habitat idea is awesome, that's quite a vision!

  Are you sure? yes | no

Morning.Star wrote 03/03/2017 at 18:28 • point

Hi RigTig, thanks for following #Cardware . Love your 3D printer project, thats really novel and awesome.

  Are you sure? yes | no

David H Haffner Sr wrote 12/07/2016 at 14:45 • point

Thank you for following my little project!

  Are you sure? yes | no

ottoragam wrote 11/09/2016 at 13:18 • point

Thanks for the follow :)

  Are you sure? yes | no

Send a private message to RigTig

Become cool instantly

Create your Hackaday.io profile like RigTig and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2023 Hackaday

Report user as inappropriate

You are about to report the user "RigTig", please tell us the reason.